Homepage Teile Vertriebs GmbH
Gerberstr. 138-142
D - 41748 Viersen / Germany
Tel.       +49 / 21 62 / 93 26 15
Fax       +49 / 21 62 /   3 36 48

e-mail
E-Mail


How to
order

Suchen
Search

 Bus T1, T2 + T3

germanenglishfrench

Beetle

Golf & Co.

Karmann Ghia

Porsche

 

Informations
- All about us -

How to order
All about us

***NEW***


First-aid box,
nostalgia collection
part no. 021 0125

Items for type 181


Door sill, inner,
left or right, piece
part no. 080 1000-01 and
080 1000-02


Door sill, outer,
left or right, piece
part no. 080 1003-01 and
080 1003-02

Engine components

page 1  I  page 2   I  page 3

SHORT BLOCK, STANDARD, 1600 CCM

Brand new short block from VW-production with new components as crank case, crankshaft, camshaft, piston and cylinders, cylinder heads and 200 mm flywheel 12V

stroke:   69 mm
drilling: 85,5 mm
cylinder heads: typ 040 standard
camshaft: standard
fly wheel: 200 mm, 12 Volt

 

 
020 0060-2 Short block, standard

EUR   2199.00
VAT included,
plus freight cost

HINT: For new engines it is fundamentaly
necessary to use new oil cooler!
In used oil coolers there will be
metal particles which cannot be removed.

ENGINE, COMPLETE, WITH STANDARD IGNITION SYSTEM, GENERATOR

With standard ignition system (009 distributer).
Engine comes complete with fan shroud, heat exchangers and 009 distributor.
With generator.

For a bigger picture please click here -->

 

 
020 0043 Engine, complete, 1600 ccm, VW Mexico, with standard ignition system and GENERATOR

EUR   3149.00
VAT included,
plus freight cost

ENGINE CHANGE OVER KIT "STANDARD"

The kit contains:

  • 2 cylinder heads, standard, cpl.
  • 4 piston and cylinders, 85,5 x 69 mm, standard, 1600 ccm
  • 1 engine gasket set, standard, 1300-1600 ccm
  • 1 flywheel oil seal
    •
  • 1 push rod tubes, 1300-1600
  • 1 tube gasket glue
 

 
020 0093 Engine change over kit, standard

EUR   525.00
VAT included,
plus freight cost

ENGINE CHANGE OVER KIT "UNLEADED"

The kit contains:

  • 2 cylinder heads 041, unleaded
  • 4 piston and cylinders, 88 x 69 mm, Slip In
  • 1 engine gasket set, standard, 1300-1600 ccm
  • 1 flywheel oil seal
  • 1 push rod tubes, 1300-1600
  • 1 tube gasket glue
 

 
020 0090-1 Engine change over kit "unleaded", Slip In

EUR   679.00
VAT included,
plus freight cost

ENGINE CHANGE OVER KIT "UNLEADED"

With this kit you can change over your 1300, 1500 and 1600 ccm engine to unleaded fuel. All standard parts are replaced by the new parts of the kit.

The kit contains:

  • 4 piston and cylinders 85,5 x 69 mm
  • 2 cylinder heads
  • 1 set of push rod tubes
  • 1 engine gasket set
  • 1 tube gasket glue
 

 
020 0090 Engine change over kit, unleaded

EUR   549.00
VAT included,
plus freight cost

ENGINE KIT  "STREET" 1679 CCM

Engine kit to start with professional tuning.

The kit contains:

  • 4 piston and cylinders 88 x 69 mm
  • 1 cam OZ 268°/Lift 8,86
  • 1 camshaft bearing set
  • 1 "Maxi" oil pump incl. lfilter
  • 1 engine gasket set compl.
  • 1 tube gasket glue
  • 1 special intake manifolds for Solex PICT carburetor
 

 
010 0060 Engine kit "Street", 1679 ccm

EUR   585.00
VAT included,
plus freight cost

ENGINE KIT "STANDARD PLUS"

Engine kit complete for tuning or complete overhaul. Can be mount with simple tools and contains only brand-new parts.

The kit contains:

  • 4 piston and cylinders 85,5 x 69 mm
  • 2 cylinder heads, standard
  • 1 crank shaft, standard, 69 mm, new
  • 1 connecting rods, standard (Set)
  • 8 valve lifters
  • 1 main bearing set, standard
  • 1 connecting rod bearing set, standard
  • 1 windage push rod tubes
  • 1 camshaft gear assembly kit without distributor drive
  • 1 camshaft bearing set
  • 1 fly wheel oil seal
  • 1 engine gasket set
  • 1 tube gasket glue
 

 
020 0095 Engine kit "Standard Plus"

EUR   929.00
VAT included,
plus freight cost

ENGINE KIT "STANDARD PLUS/PLUS"

Engine kit complete for tuning or complete overhaul. Can be mount with simple tools and contains only brand-new parts.

The kit contains:

  • 4 piston and cylinders 85,5 x 69 mm
  • 2 cylinder heads 041, unleaded
  • 1 crank shaft, standard, 69 mm, new
  • 1 connecting rods, standard (Set)
  • 8 valve lifters
  • 1 main bearing set, standard
  • 1 connecting rod bearing set, standard
  • 1 windage push rod tubes
  • 1 camshaft gear assembly kit without distributor drive
  • 1 camshaft bearing set
  • 1 fly wheel oil seal
  • 1 engine gasket set
  • 1 tube gasket glue
020 0095-07 Engine kit "Standard Plus / plus"

EUR   929.00
VAT included,
plus freight cost

ENGINE KIT  "NEW RACE" 1776 CCM

1.8 l engine kit special for two single carburetors.

The kit contains:

  • 4 piston and cylinders, 90,5 x 69 mm
  • 1 cam OZ 280° / Lift 8,64
  • 1 "Maxi" oil pump incl. filter
  • 1 engine gasket set
  • 1 crank shaft 69 mm
  • 1 hot rod set
  • 1 main bearing set
  • 1 connecting rod set
  • 1 fly wheel oil seal
  • 1 tube gasket glue
 

 
010 0070 Engine kit "New Race" 1776 ccm

EUR   839.00
VAT included,
plus freight cost

WASHER, CYLINDER HEAD

Type 1, 1.2-1.6

 

 
010 1003-09 Washer for cylinder head, 10 mm, .56-

EUR   0.49
VAT included,
plus freight cost
 

 
010 1003-10 Washer for cylinder head, 8 mm, .56-

EUR   0.70
VAT included,
plus freight cost

FIXING NUT FOR CYLINDER HEAD

Type 1, 1.2-1.6

 

 
010 1003-12 Fixing nut for cylinder head, 10 mm, .56-

EUR   1.00
VAT included,
plus freight cost
 

 
010 1003-13 Fixing nut for cylinder head, 8 mm, .56-

EUR   1.00
VAT included,
plus freight cost

STUD KIT, 8 MM, DUAL PORT HEADS

Stud kit for dual port heads, fit for standard crank case. Manufactured of special steel. Comes in set of 16 pieces incl. nuts and washers.

Length: 9 pieces = 23.5 cm, 3 pieces = 19.9 cm und 4 pieces = 18.5 cm

 

 
010 1001 Stud kit, 8mm, dual port heads, 1500-1600 ccm

EUR   28.00
VAT included,
plus freight cost

SELF TAPPING CASE STUDS, 10 MM

For quick repair of stripped head studs. The rolled-thread of these 10 mm studs provide maximum hold and metal chips are effectively collected by the slot or hole design (see enlargement in picture)

 

 
010 1003-03 Stud, 10 mm, 178 mm, 1200 ccm, upper, piece

EUR   6.50
VAT included,
plus freight cost
 

 
010 1003-04 Stud, 10 mm, 230 mm, 1200 ccm, lower, piece

EUR   6.50
VAT included,
plus freight cost
 

 
010 1003-05 Stud, 10 mm, 204 mm, 1500-1600 ccm, upper, piece

EUR   6.90
VAT included,
plus freight cost
 

 
010 1003-06 Stud, 10 mm, 240 mm, 15-1600 ccm, lower, piece

EUR   6.90
VAT included,
plus freight cost

CASE SAVER INSERTS

Repair stripped and worn head stud threads. Case savers provide greater hold.

 

 
010 0999 Case saver inserts, 14/10mm, pair

EUR   2.10
VAT included,
plus freight cost

CRANK CASE

New standard crank case with 12 mm main oilpressure canal and 12 mm thread inserts. The casting is made of stable AS 41 alloy (4%aluminium, 1% silicium). Thus the crank case is more stable than the former cases of AS 21 alloy.

010 0003 Crank case, standard, 1300-1600

EUR   489.00
VAT included,
plus freight cost
 

 
010 0003-01 Crank case, standard, original part, 1300-1600

EUR   530.00
VAT included,
plus freight cost

Crank cases are also available rebored.

010 0003-10 Crank case, rebored for 90.5 or 92 mm cylinders

EUR   595.00
VAT included,
plus freight cost
010 0003-20 Crank case, rebored for 94 mm cylinders

EUR   595.00
VAT included,
plus freight cost

CRANK CASE, ELECTRICAL FUEL PUMP, ORIGINAL PART

Like 010 0003-01 but without openings for fuel pump, no attach for Bus engine support (3 drillings)

 

 
010 0003-04 Crank case, eletrical fuel pump, original part

EUR   575.00
VAT included,
plus freight cost

CAMSHAFT END PLUG RUBBER

Should be renewed on each engine check.

 

 
010 1014 Plastic end plug rubber, camshaft

EUR   2.90
VAT included,
plus freight cost
 

 
010 1014-01 Metal end plug rubber, camshaft

EUR   3.50
VAT included,
plus freight cost

OIL SUCK IN TUBE

 

 
010 0005-03 Oil suck in tube, type 1, 14 mm

EUR   21.00
VAT included,
plus freight cost

CRANK CASE REPAIR KIT

German OE-quality.

 

 
010 1005 Crank case repair kit

EUR   17.90
VAT included,
plus freight cost

ENGINE HARDWARE KIT

Complete set of high quality nuts, washers, etc. for engine assembly.

 

 
020 0268 Engine hardware kit

EUR   24.80
VAT included,
plus freight cost

STOP NUT SET FOR CRANK CASE TYPE 1

 

 
020 0270 Stop nut set for crank case type 1

EUR   5.50
VAT included,
plus freight cost

CRANK SHAFT, STANDARD, NEW

 

 
010 0013 Stock crankshaft, standard, new

EUR   169.00
VAT included,
plus freight cost

CRANK SHAFT, FORGED

Forged counter-weighted crank shaft for stock rods.

 

 
010 0009 Crank shaft, forged, 76 mm

EUR   359.00
VAT included,
plus freight cost
010 0010 Crank shaft, forged, 78 mm

EUR   499.00
VAT included,
plus freight cost

PUSH ROD TUBES

 

 
092 0385 Push rod tube set, Bus T2 and T3, 1.7-2.0, 8.71-12.82

EUR   49.90
VAT included,
plus freight cost

PUSH ROD TUBE SEALS, TYPE 4

 

 
092 0530 Push rod tube seals, type 4,
Bus T2 and T3, 1.7-2.0, 8.71-12.82, set

EUR   12.00
VAT included,
plus freight cost

OIL COOLER, STANDARD

 

 
092 0720 Oil cooler, standard, Bus T2 and T3, 1.7-2.0, 8.71-12.82

EUR   99.50
VAT included,
plus freight cost

page 1  I  page 2   I  page 3

 



Hoffmann Speedster Teile Vertriebs GmbH
 Gerberstr. 138-142
D - 41748 Viersen
Tel: +49 / 21 62 / 93 26 15
Fax: +49 / 21 62 / 3 36 48
e-mail: info@hoffmann-speedster.com